PA6-LGF PA6 개질 플라스틱은 순수한 PA6 조각을 모체로 하고 혼합, 충전, 강화, 공중합, 가교 및 기타 방법을 통해 내부 및 외부 특성을 개선하여 PA6 응용 분야의 약 15%를 차지합니다. 긴 유리 섬유 함량은 20%-60%이며, 긴 유리 섬유 함량은 다른 제품 특성에 따라 제어됩니다. 그것은 고강도, 우수한 내열성, 우수한 내 충격성의 특성을 가지고 있으며 일부 금속 재료의 경량을 대체 할 수 있습니다. 전동 공구 쉘, 정원 도구, 기어, 스포츠 장비, 자동차 부품 등에 널리 사용됩니다. PA6-LGF의 다른 사양 난연성 PA6 PA6 material has poor flame retardant performance and belongs to flammable materials, but flame retardants can change the combustion characteristics of polymers. Through mechanical mixing method, flame retardants are added to the master material to change the flammable characteristics. The products are divided into: nitrogen flame retardants, phosphorus flame retardants, environmental protection bromine flame retardants, mineral filled flame retardants, which can be used in switches, low-voltage electrical housing, wiring terminals, circuit breakers, etc. Toughen PA6 Mixed with an appropriate amount of toughening agent, the product has the characteristics of low temperature resistance, high flexibility, high fluidity, low shrinkage, low water absorption, high impact resistance, aging resistance and so on. It can be used for baby carriage parts, rolling belts, line clips, connectors and so on. Application In addition to the above applications, in high-end fields such as rail transit, medical treatment, military industry and aerospace, nylon 6 modified plastics are used more and more widely, and PA6 modified plastics are used everywhere in daily life. TDS for reference Nylon reinforced material is made of PA6/PA66 resin as the base material and adding a certain proportion of glass fiber modification. Because nylon itself is not strong enough, by adding 20 to 60 percent of the fiber, to increase its strength. In particular, 30% strength is considered the most appropriate ratio. Also added to 40-50%, according to the specific requirements of different products, coupled with the appropriate formula, can be successful. Advantage of Long glass fiber compounds 1. After glass fiber reinforcement, glass fiber is a high temperature resistant material, therefore, the heat resistance temperature of reinforced plastics is much higher than before without glass fiber, especially nylon plastics; 2. After glass fiber reinforcement, due to the addition of glass fiber, limited the mutual movement between polymer chains of plastics, therefore, the shrinkage rate of reinforced plastics decreases a lot, rigidity is greatly improved; 3. After glass fiber reinforcement, the reinforced plastic will not stress crack, at the same time, the anti-impact performance of plastic is improved a lot; 4. After glass fiber reinforcement, glass fiber is a high strength material, which also greatly improves the strength of plastic, such as: tensile strength, compression strength, bending strength, improve a lot; 5. glass fiber reinforced after, due to the addition of glass fiber and other additives, the combustion performance of reinforced plastics decreased a lot, most of the material can not ignite, is a kind of flame retardant material. Xiamen LFT composite plastic Co., Ltd. Xiamen LFT composite plastic Co., Ltd. is a brand-name company that focuses on LFT&LFRT. Long Glass Fiber Series (LGF) and Long Carbon Fiber Series (LCF). The company's thermoplastic LFT can also be used for LFT-D molding. It can be produced according to customer requirements: 5~25mm length. The company's long-fiber continuous infiltration reinforced thermoplastics have passed ISO9001&16949 system certification, and the products have obtained lots of national trademarks and patents.

What is HDPE? High density polyethylene (HDPE) is a white powder or granular product. Non-toxic, tasteless, crystallinity is 80% ~ 90%, softening point is 125 ~ 135℃, the use of temperature can reach 100℃; The hardness, tensile strength and creep property are better than low density polyethylene. Good wear resistance, electrical insulation, toughness and cold resistance; Good chemical stability, at room temperature, insoluble in any organic solvent, acid, alkali and all kinds of salt corrosion resistance; Thin film to water vapor and air permeability is small, low water absorption; Poor aging resistance, environmental stress cracking resistance is not as good as low density polyethylene, especially thermal oxidation will reduce its performance, so the resin must be added in antioxidants and ultraviolet absorbent to improve this deficiency. Filling Long glass fiber The tensile strength of polyethylene can be improved obviously when the amount of glass fiber is 30% ~ 40%. With the continuous increase of the addition amount, the increase of tensile strength did not change significantly, but tended to be stable. The addition amount of glass fiber has a great influence on the elastic modulus of polyethylene plastic materials. With the increase of glass fiber addition amount, the elastic modulus of polyethylene plastic materials will continue to increase and reach a certain value. 유리 섬유의 첨가는 폴리에틸렌 플라스틱 재료의 파단 신율에 큰 영향을 미칩니다. 유리 섬유의 첨가가 증가함에 따라 폴리에틸렌 플라스틱 재료의 파단 연신율은 계속해서 감소할 것입니다. 특정 값까지 유리 섬유 개질 폴리에틸렌의 취성은 유리 섬유 취성과 거의 동일하게 더 분명합니다. 참고용 TDS 애플리케이션 공장 창고 및 패키지 팀 및 고객 우리는 당신에게 다음을 제공할 것입니다: 1. LFT 및 LFRT 재료 기술 매개변수 및 최첨단 설계. 2. 금형 전면 디자인 및 권장 사항. 3. 사출 성형 및 압출 성형과 같은 기술 지원을 제공합니다.

PPS The molecular structure of PPS consists of benzene ring and sulfur atoms interarranged, the configuration is orderly, easy to form a high thermal stability of the crystal structure. At the same time, the molecular structure of PPS material has a highly stable chemical bond characteristics, the benzene ring structure makes PPS more rigid, and the sulfur ether bond (-S-) provides a certain degree of flexibility. PPS itself has good heat resistance, flame retardant, chemical resistance, should be a promising material, but unmodified PPS has some unavoidable defects: Difficult processing:  This is the biggest pain point of all high temperature resistant materials -- high processing temperature, no matter the molding process or processing energy consumption, will face great challenges. In addition, PPS is still prone to thermal oxidation crosslinking in the melting process, resulting in reduced fluidity and further improve the processing difficulty; Poor toughness: PPS molecular chain is rigid, the maximum crystallinity is as high as 70%, the elongation is low and the welding strength is not so good. As a result, the impact resistance of unmodified PPS is poor, which limits the application scope. High cost: PPS raw materials and general engineering plastics compared, the price is about 1-2 times higher, and some modified materials compared with low cost performance; Difficult coating: PPS surface coating and coloring performance is not ideal. While this is not a major problem for now, it is a limiting factor. PPS-LGF Long glass fiber reinforced composites can solve your problems when other methods of reinforced plastics do not provide the performance you need or if you want to replace metal with plastic. Long glass fiber reinforced composites can cost-effectively reduce the cost of goods and effectively improve the mechanical properties of engineering polymers, and increase the durability by forming long fibers to form a long-fiber-reinforced internal skeleton network. Performance is preserved in a wide range of environments. 참고용 TDS 애플리케이션 회사 소개 Xiamen LFT composite plastic Co., Ltd.는 LFT&LFRT에 주력하는 브랜드 회사입니다. 긴 유리 섬유 시리즈(LGF) 및 긴 탄소 섬유 시리즈(LCF). 열가소성 LFT는 LFT-G 사출 성형 및 압출에 사용할 수 있으며 LFT-D 성형에도 사용할 수 있습니다. 그것은 고객 요구에 따라 생성할 수 있습니다: 5~25mm 길이. 회사의 장섬유 연속 침투 강화 열가소성 플라스틱은 ISO9001&16949 시스템 인증을 통과했으며 제품은 많은 국가 상표 및 특허를 획득했습니다.

PA12 PA12 polyamide or nylon 12 Chemical and physical properties of PA12 PA12 is a linear, semi-crystalline - crystalline thermoplastic material from butadiene. Its properties are similar to PA11, but its crystal structure is different. PA12 is a good electrical insulator and will not be affected by moisture as other polyamides. PA12 has good impact resistance mechanical and chemical stability. There are many improved varieties of PA12 in terms of plasticizing and reinforcing properties. Compared with PA6 and PA66, these materials have lower melting point and density, and have very high moisture recovery. PA12 has no resistance to strong oxidizing acids. The viscosity of PA12 depends mainly on humidity, temperature and storage time. PA12 It's very liquid. The shrinkage rate of PA12 is between 0.5% and 2%, depending on the variety of PA12 material, wall thickness and other process conditions. PA12 compounds plastic Nylon glass fiber material is a kind of composite material, adding glass fiber on the basis of the original nylon material, so that the material has the following characteristics: High temperature resistance, good dimensional stability, good toughness, good insulation, corrosion resistance, high mechanical strength. LGF & SGF Compared with the short fiber, it has more excellent performance in mechanical properties. It is more suitable for large products and structural parts. It has 1-3 times higher (toughness) than short fiber, and the tensile strength (strength and rigidity) is increased by 0.5-1 times. Datasheet for reference Application ■ Power tools: cutting machine, electric saw, electric drill, Angle grinder, polishing machine, electric hammer, electric pick, hot air gun and other models; ■ Automotive industry: cooling chamber, intake manifold, frame bracket, ventilation grille, door handle, throttle body and other models; ■ 기계 산업: 워터 펌프, 워터 밸브, 베어링, 샤프트 슬리브, 기어, 브래킷 및 기타 모델; ■ 스포츠 장비: 스키 장비, 유모차, 피트니스 장비 부품 및 기타 모델; ■ 사무기기: 시트 브래킷, 도르래, 회전축, 분쇄기 기어, 프린터 부품 및 기타 모델; 인증 공장 패키지 왜 우리를 선택 했습니까

PPA 소재 고온 나일론은 중축합 반응을 통해 테레프탈산 또는 프탈산과 지방족 디아민으로 만들어진 반방향족 폴리아미드 중합체입니다. 그것의 분자 사슬은 벤젠 고리와 디아민 유연한 긴 사슬을 포함하므로 높은 결정화 속도와 결정화도를 가지고 있습니다. PPA 엔지니어링 플라스틱은 고온 나일론을 기본 재료로 하는 섬유로 강화된 고성능 엔지니어링 플라스틱입니다. 고온 나일론의 구조 및 결정화 특성은 나일론 66, 나일론 6 및 기타 엔지니어링 플라스틱보다 더 많은 특성과 우수한 전체 성능을 제공합니다: 강한 강성, 높은 경도, 고온 저항, 우수한 내 화학성 및 낮은 수분 흡수, 치수 정확도 및 안정성과 낮은 휘어짐, 우수한 내피로성, 자동차 부품, 기계 부품, 전기 전자 부품 등 많은 분야에서 자동차 부품, 회로 차단기 등에 널리 사용됩니다. PPA-LGF 소재 1, 강하고 단단하고 강한 강성, 높은 경도, 낮은 뒤틀림 2, 우수한 인성 3, 우수한 내 화학성 우수한 내 화학성 4, PPA는 수분 흡수율의 영향을 받고 우수한 치수 정확도, 안정성 및 낮은 뒤틀림 5, 작은 플로트, 표면 스프레이 및 전기 도금 가능 6, 금속과의 높은 결합력, 철 플라스틱 분리시 온도 변화 및 크기 형성 방지 참조용 TDS 생산 과정 애플리케이션 저전압 스위치, 회로 차단기, 기계 부품, 자전거 액세서리 등 회사 소개 Xiamen LFT composite plastic Co., Ltd는 LFT&LFRT에 중점을 둔 브랜드 회사입니다. 긴 유리 섬유 시리즈(LGF) 및 긴 탄소 섬유 시리즈(LCF). 이 회사의 열가소성 LFT는 LFT-G 사출 성형 및 압출에 사용할 수 있으며 LFT-D 성형에도 사용할 수 있습니다. 그것은 고객 요구에 따라 생성될 수 있습니다: 길이 5~25mm. 회사의 지속적인 침투 강화 열가소성 플라스틱은 ISO9001&16949 시스템 인증을 통과했으며 제품은 많은 국가 상표 및 특허를 획득했습니다.

MXD6 Polyadipyl-m-benzoylamine, referred to as mxd6, generally referred to as "nylon mxd6", resin than other engineering plastics have higher mechanical strength and modulus, is also a special high barrier nylon material. Although the barrier of mxd6 is slightly worse than that of pvdc and evoh, its barrier is not affected by temperature and humidity, which is especially suitable for high temperature and humid occasions. In today's barrier packaging and plastic instead of steel general trend, nylon mxd6 has become one of the most eye-catching new plastic varieties. Structure performance: PA MXD6 nylon material has high strength, high rigidity, high thermal deformation temperature, small thermal expansion coefficient; Dimensional stability, low water absorption rate and small size change after water absorption, mechanical strength changes less; Forming shrinkage is small, suitable for precision forming processing; Excellent coating performance, especially suitable for high temperature surface coating; Excellent barrier to oxygen, carbon dioxide and other gases. Excellent mechanical and thermal properties and high strength, high modulus and heat resistance, high barrier, excellent cooking resistance Advantages 1、Maintain high strength and rigidity in a wide temperature range 2、High heat deflection temperature, small coefficient of thermal expansion 3、Low water absorption, small size change after water absorption, less mechanical strength reduction 4、Small shrinkage rate of molding, suitable for precision molding process 5、Excellent paintability, especially suitable for surface painting under high temperature 6、Excellent barrier to oxygen, carbon dioxide and other gases MXD6-LGF MXD6 applications in the plastics modification industry MXD6 can be compounded with glass fibers, carbon fibers, minerals and/or advanced fillers for materials containing 50-60% glass fiber reinforcement with exceptional strength and stiffness. Even when filled with high levels of glass fiber, its smooth, resin-rich surface creates a high gloss finish like no glass fiber, making it ideal for painting, metal coating or creating naturally reflective housings. 1、High fluidity for thin wall It is a very high flowing resin that can easily fill thin walls as thin as 0.5 mm thick even with glass fiber content as high as 60%. 2、Excellent surface finish The resin-rich perfect surface has a highly polished appearance, even with a high glass fiber content. 3、Very high strength and stiffness MXD6 with 50-60% glass fiber reinforcement has a tensile and flexural strength similar to many cast metals and alloys. 4、Good dimensional stability At ambient temperature, the coefficient of linear expansion (CLTE) of MXD6 glass fiber composite is similar to that of many cast metals and alloys. It is highly reproducible due to low shrinkage and the ability to maintain tight tolerances (length tolerances can be as low as ± 0.05% if properly formed). 참조용 TDS 애플리케이션 MXD6는 금속을 대체하여 자동차, 전자 제품 및 전기 제품의 고품질 구조 부품을 만듭니다. 자동차 부품에서는 기계적 강도가 높고 내유성이 좋은 소재 제품이 필요한 경우가 많으며 120~160℃ 범위에서 장기간 사용할 수 있습니다. 유리섬유가 강화된 MXD6는 225℃까지의 내열성과 고온에서 높은 강도 유지율을 가지고 있어 자동차 엔진의 실린더 블록, 실린더 헤드, 피스톤, 동기 기어 등에 사용할 수 있습니다. MXD6/PPO 합금은 고온 저항, 고강도, 내유성, 내마모성, 우수한 치수 안정성 등의 특성을 가지고 있습니다. 자동차 차체의 수직 외부 패널, 앞뒤 펜더, 휠 커버에 사용할 수 있으며 스탬핑 및 성형이 거의 불가능합니다. 강판. 자동차의 곡선 부품 및 섀시. 회사 소개

PP material PP is a polymer made of propylene as monomer by coordination polymerization, and is one of the five major general-purpose plastics PE, PP, PVC, PS and ABS. 1. colorless, tasteless, five toxic, unadded PP material compounded with FDA and other food-grade material requirements; 2. due to the crystalline nature of PP, the original color milky white translucent, better transparency than PE; 3. low specific gravity of 0.9, almost one of the lightest plastics than water; 4. good toughness, especially repeated resistance to bending ability, commonly known as 100 fold rubber; 5. better heat resistance than PE, which can reach up to 120°C; 6. good resistance to hydrolysis and can be sterilized by high temperature steam 7. good chemical resistance, especially acid resistance, can be due to the storage of concentrated sulfuric acid containers; 8. outdoor use is susceptible to light, ultraviolet light and other aging. 수정된 PP 재료 탄소 섬유로 채워진 PP 재료는 PP 재료의 강성과 모듈러스를 증가시키고 수축으로 인한 재료 변형을 줄일 수 있지만 동시에 재료 인성은 감소합니다. 항 UV제를 첨가함으로써 노화 방지제는 PP의 옥외 사용 성능을 향상시킬 수 있으며 난연성 물질을 첨가하면 PP의 난연성을 향상시킬 수 있습니다. 참조용 TDS SGF 대 LGF 긴 탄소 섬유 사양 애플리케이션 제품 가공 우리는 당신을 제안할 것입니다 1. LFT&LFRT 소재 기술 파라미터 및 최첨단 설계 2. 금형 전면 설계 및 권장 사항 3. 사출성형, 압출성형 등 기술지원

폴리아미드6 나일론 6 (PA6) 일반 엔지니어링 플라스틱으로 경량, 내마모성, 내식성, 우수한 인성 및 기타 특성을 가지며 일반적인 열가소성 수지로 가열 연화, 냉각 경화 및 반복 가열 가능 연화, 냉각 경화, 반복 가공 특성. 긴 탄소 섬유 탄소섬유 직물은 고강도, 고탄성률, 큰 비표면적 및 종횡비, 높은 전기전도도 등으로 유리섬유에 비해 우수한 기계적 물성을 가지며 섬유방향으로 최대강도를 제공할 수 있다. 탄소 섬유 강화 복합 재료는 폴리머 매트릭스 재료보다 더 강하면서도 가벼운 무게의 장점을 유지하며 전자 제품, 전기 자동차, 의료 기기, 산업 장비 및 스포츠 및 레저 제품 분야에서 점차 전통적인 금속 재료를 대체하고 있습니다. LCF 대 SCF LCF의 장점 (1) 고강도 및 고인성 (2) 열팽창 계수가 작음 (3) 경도가 낮고 무게가 가벼움 (4) 내식성 및 내노화성 (5) 내열성 참고용 TDS 애플리케이션 헬멧, 자동차 범프 및 로봇 팔 등 제조에 적합합니다. 인증 사출 성형 공장 및 창고 팀 및 고객 회사 소개 Xiamen LFT composite plastic Co., Ltd는 LFT&LFRT에 중점을 둔 브랜드 회사입니다. 긴 유리 섬유 시리즈(LGF) 및 긴 탄소 섬유 시리즈(LCF). 이 회사의 열가소성 LFT는 LFT-G 사출 성형 및 압출에 사용할 수 있으며 LFT-D 성형에도 사용할 수 있습니다. 그것은 고객 요구에 따라 생성될 수 있습니다: 길이 5~25mm. 회사의 지속적인 침투 강화 열가소성 플라스틱은 ISO9001&16949 시스템 인증을 통과했으며 제품은 많은 국가 상표 및 특허를 획득했습니다.

Long carbon fiber Carbon fiber has many excellent properties, high axial strength and modulus, low density, high specific performance, no creep, super high temperature resistance in non-oxidizing environment, good fatigue resistance, specific heat and electrical conductivity between non-metal and metal, small coefficient of thermal expansion and anisotropy, good corrosion resistance, good X-ray transmission. Good electrical and thermal conductivity, good electromagnetic shielding, etc. Compared with traditional glass fiber, carbon fiber has more than 3 times of Young's modulus; it is about 2 times of Young's modulus compared with Kevlar fiber, which is insoluble and swollen in organic solvents, acids and alkalis, and has outstanding corrosion resistance. But is there a way to reduce the price of carbon fiber? That is to mix it with relatively cheap nylon material to form a composite material with good performance and meet the requirements. In that case, there is no doubt that carbon fiber nylon will definitely have a place in the composite material. Nylon itself is an engineering plastic with excellent performance, but moisture absorption, poor dimensional stability of products. Strength and hardness are also far from metal. In order to overcome these shortcomings, as early as before the 70s. People have used carbon fiber or other varieties of fibers for reinforcement to improve its performance. Carbon fiber reinforced nylon materials have developed rapidly in recent years, because nylon and carbon fiber are excellent performance in the field of engineering plastics materials, its compound material synthesis reflects the superiority of the two, such as strength and rigidity than unreinforced nylon is much higher, high temperature creep is small, thermal stability has improved significantly, good dimensional accuracy, wear resistance. Excellent damping, compared with glass fiber reinforced has better performance. Therefore, carbon fiber reinforced nylon (CF / PA) composites have developed rapidly in recent years. And for 3D printing using SLS technology is the most suitable technical means to achieve carbon fiber reinforced nylon. 참고용 TDS 애플리케이션 우리 회사 Xiamen LFT composite plastic Co., Ltd는 LFT&LFRT에 중점을 둔 브랜드 회사입니다. 긴 유리 섬유 시리즈(LGF) 및 긴 탄소 섬유 시리즈(LCF). 이 회사의 열가소성 LFT는 LFT-G 사출 성형 및 압출에 사용할 수 있으며 LFT-D 성형에도 사용할 수 있습니다. 그것은 고객 요구에 따라 생성될 수 있습니다: 길이 5~25mm. 회사의 지속적인 침투 강화 열가소성 플라스틱은 ISO9001&16949 시스템 인증을 통과했으며 제품은 많은 국가 상표 및 특허를 획득했습니다.

What is carbon fiber PLA? Carbon fiber reinforced PLA is an excellent material, strong, lightweight, with excellent layer bonding and low warpage. It has excellent layer adhesion and low warpage. Carbon fiber filaments are not as strong" as other 3D materials, but are much stiffer. The increased rigidity of carbon fiber means increased structural support, but reduced overall flexibility. It is slightly more brittle than regular PLA.  Carbon PLA Specifications Flexural strength: 57 MPa Melting temperature: 190°C- 230°C Tensile strength: 45.5 MPa . Elongation at break: (73°F) 320% Standard tolerance: 0.05mm Layer thickness: 3mm Shore hardness: 45D Density: 1.3 g/cm3 (1300 kg/m3) Heat distortion: 21% to 85°C Shrinkage: very low when cooled to higher ambient temperatures Characteristics Moderate strain at break (8-10%), so the filaments are not very brittle, but very tough Very high melt strength and viscosity Good dimensional accuracy and stability Easy handling on many platforms Highly attractive matte black surface Excellent impact resistance and lightness Applications of carbon fiber PL A material Carbon PLA is the ideal material for frames, supports, housings, propellers, chemical instruments, etc. It is also particularly preferred by drone manufacturers and RC enthusiasts. Ideal for applications requiring maximum stiffness and strength. Other products you may wonder                      PA6-LCF                                    PP-LCF                                   PEEK-LCF About Long carbon fiber Long carbon fiber reinforced composites offer siginifacant weight savings and provide optimum strength and stiffness properties in reinforced thermoplastics. The excellent machanical properties of long carbon fiber reinforced composites make it an ideal replacement for metals. Combined with the design and manufacturing advantages of injection molded thermoplastics, long carbon fiber composites simplify the re-imagining of components and equipment with demanding performance requirements. Its widespread use in aerospace and other advanced industries makes it a "high-tech" perception of consumers - you can use it to market products and create differentiation from competitors. About us Xiamen LFT composite plastic Co., Ltd는 LFT&LFRT에 중점을 둔 브랜드 회사입니다. 긴 유리 섬유 시리즈(LGF) 및 긴 탄소 섬유 시리즈(LCF). 이 회사의 열가소성 LFT는 LFT-G 사출 성형 및 압출에 사용할 수 있으며 LFT-D 성형에도 사용할 수 있습니다. 그것은 고객 요구에 따라 생성될 수 있습니다: 길이 5~25mm. 회사의 지속적인 침투 강화 열가소성 플라스틱은 ISO9001&16949 시스템 인증을 통과했으며 제품은 많은 국가 상표 및 특허를 획득했습니다. 다음을 제공할 수 있습니다. 1. LFT 및 LFRT 재료 기술 매개변수 및 최첨단 설계. 2. 금형 전면 디자인 및 권장 사항. 3. 사출 성형 및 압출 성형과 같은 기술 지원을 제공합니다.

호모 PP란? Homopolymerized PP 플라스틱은 단일 프로필렌 단량체를 중합하여 만들어지며 분자 사슬에 에틸렌 단량체를 포함하지 않습니다. Homopolymerized 폴리프로필렌 pp 플라스틱은 더 나은 강도의 장점이 있습니다. 단점은 열악한 내충격성(더 부서지기 쉬움), 열악한 인성, 열악한 치수 안정성, 쉬운 노화 및 열악한 장기 열 안정성 성능입니다.  열가소성 폴리머인 PP는 1957년에 상업 생산을 시작했으며 규제 대상인 독립형 폴리머 중 첫 번째입니다. 그것의 역사적 중요성은 가장 빠르게 성장하는 주요 열가소성 수지였으며 열가소성 분야, 특히 섬유 및 필라멘트, 필름 압출 및 사출 성형 공정에서 매우 광범위한 응용 분야를 가지고 있다는 사실에 더욱 반영됩니다. HPP-LCF 긴 탄소 섬유 강화 복합재는 상당한 중량 절감 효과를 제공하고 강화 열가소성 수지에서 최적의 강도 및 강성 특성을 제공합니다. 긴 탄소 섬유 강화 복합 재료의 우수한 기계적 특성으로 인해 금속을 이상적으로 대체할 수 있습니다. 사출 성형된 열가소성 수지의 설계 및 제조상의 이점과 결합된 긴 탄소 섬유 복합재는 까다로운 성능 요구 사항이 있는 구성 요소 및 장비의 재구상을 단순화합니다. 항공 우주 및 기타 첨단 산업에서 광범위하게 사용되어 소비자에게 "하이테크" 인식을 부여합니다. 이를 사용하여 제품을 마케팅하고 경쟁업체와 차별화할 수 있습니다. 애플리케이션 응용 프로그램에 대한 자세한 내용은 당사에 문의하십시오. 참조용 데이터시트 단섬유 VS 장섬유 긴 탄소 섬유 Xiamen LFT 복합 플라스틱 Co., Ltd Xiamen LFT composite plastic Co., Ltd는 LFT&LFRT에 중점을 둔 브랜드 회사입니다. 긴 유리 섬유 시리즈(LGF) 및 긴 탄소 섬유 시리즈(LCF). 이 회사의 열가소성 LFT는 LFT-G 사출 성형 및 압출에 사용할 수 있으며 LFT-D 성형에도 사용할 수 있습니다. 그것은 고객 요구에 따라 생성될 수 있습니다: 길이 5~25mm. 회사의 지속적인 침투 강화 열가소성 플라스틱은 ISO9001&16949 시스템 인증을 통과했으며 제품은 많은 국가 상표 및 특허를 획득했습니다.

소재 소개 1935년 DuPont의 과학 연구원인 Wallace Carothers와 그의 팀은 처음으로 아디프산과 아디프산 디아민의 축합에 의해 PA66 합성에 성공했고, DuPont은 1939년 PA66 섬유의 상업 생산을 완료했습니다. 1950년대부터 PA , PA6, PA66 등 산업용 제품의 경량화 및 원가절감을 요구하는 금속을 대체하는 사출성형 제품 생산을 위해 개발되었습니다. 현재 PA66은 PA6 외에 가장 많이 사용되는 PA 종입니다. PA66 학명: Polyhexanediamide 약어: PA66 일반명: Nylon 66  PA66 has many similarities with PA6. PA66 is also a transparent to milky white granule that can take on almost any color with the addition of a colorant (masterbatch) specific for polymers. Material properties Similar to the basic properties of PA6, PA66 also has low specific gravity, high tensile strength, wear resistance, good self-lubrication, and excellent impact toughness. In addition, because the number of hydrogen bonds in PA66 is more than in PA6, the intermolecular force of PA66 is stronger than the intermolecular force of PA6, which makes the internal structure of PA66 more compact than PA6, with better thermal properties, higher rigidity and toughness, better dimensional stability, lower water absorption, and more wear resistance. However, PA66 has a higher market price than PA6 and is not as easy to process and mold as PA6. Like PA6, PA66 can also add a certain percentage of glass fiber, carbon fiber, etc. to improve the performance and meet the application needs of different products. The following table is a PA66-LCF30 performance table produced by Xiamen LFT composite plastic company. Materials Application PA66 has higher hardness, mechanical strength, toughness, self-lubrication, friction resistance, heat resistance after the addition of carbon fiber, and is widely used in automotive parts, electrical and electronic, as well as mechanical and engineering parts and other fields. Automotive parts PA66's low specific gravity, high rigidity, strong toughness, heat resistance and gasoline resistance make it widely used in automotive modules, automotive structural parts, automotive interior and exterior parts, automotive transmission system and chassis shield, automotive fuel system, automotive ignition system, etc. The products involve automotive cable channel modules, structural parts of front-end components of automotive sunroof system, automotive rearview mirror bracket, automotive radiator, headlight support frame, door module, seat structural parts, seat shell and backrest, dashboard skeleton, air cooler fan, etc. Electrical and electronics PA66's good insulation, flame retardancy and corrosion resistance make it suitable for making various connectors, switches, sockets, terminal blocks, wire coverings, wire ties, insulating spacers, circuit breaker housings, transformer bobbins, retaining clips and motor parts after glass fiber reinforcement. Mechanical and engineering parts PA66's good rigidity, toughness, self-lubricating properties, heat and abrasion resistance make it suitable for manufacturing various nuts, screws, cable ties, worm gears, rotating wheels, gears, pump impellers, pulley sleeves, bushings, solenoid distribution valve seats, power tool housings, pipes, luggage racks, fan housings, appliance housings, door and window frames, cable drag chains and large machine tool baffles. Details Number Color Length Sample Package MOQ Delivery time Port of Loading PA66-NA-LCF30 Natural color (can be customized) 12mm about (can be customized) Available 20kg/bag 20kg 7-15 days after shipment Xiamen Port Other products you may wonder                       pa6-lcf                                    pa12-lcf                                  peek-lcf Frequently asked questions Q. How to choose the reinforcement method and length of the material when using long fiber reinforced thermoplastic material? A.  The selection of materials depend on the requirements of the products. It is necessary to access how much the content is enhanced and how much length is more appropriate, which are depending on the performance requirements of the products. Q. Under what circumstances can long fiber replace short fiber? What are the common alternative materials? A. Traditional staple fiber materials can be replaced with long glass fiber and long carbon fiber LFT materials in the case of customers whose mechanical properties cannot be met or where higher metal substitutes are desired. For example, PP long glass fiber is often replacing nylon reinforced glass fiber, and nylon long glass fiber is replacing PPS series. Q. Are there any special process requirements of long carbon fiber for the injection molding products? A. We must consider the requirements of long carbon fiber for the injection molding machine screw nozzle, mold structure and injection molding process.  Long carbon fiber is a relatively high cost material, and need to evaluate the...